Operating treatments of drifting fish feed equipment
1. Running treatments of floating fish feed machine
( 1) Safety measures prior to starting as well as after quiting
① Examine all parts of fish feed drifting pellet making equipment, especially the attaching screws and anchor screws of each section of the puffing chamber, the connecting screws in between the electric motor base as well as the framework, and also the bolt link in between the puffing chamber and the frame, as well as there have to be no looseness;
② By hand turn the major shaft, currently, there must be no massaging noise in the fish feed drifting pellet making equipment puffing tooth cavity;
③ Begin the feeding auger of fish feed floating pellet making machine, inspect its stepless high-speed performance, and call for typical procedure;
④ Check as well as cleanse the water and gas paths prior to starting the fish feed drifting pellet making device, and all filters need to be cleansed;
Related post: fish feed mill plant cost
⑤ Prior to starting the fish feed floating pellet making maker, examine whether the circuitry of the electrical control part is appropriate, whether the rotation of each motor is correct, and also whether the control is dependable;
⑥ After the fish feed floating pellet making machine is stopped, you need to use high-temperature gloves, rapidly get rid of the discharge mold, and promptly tidy it while it is hot, as well as begin the main motor to clear the material gathered in the puffing cavity. When the corn is blown, soybean powder must be added The material is rinsed tidy;
⑦ Focus on safety and security when unloading the machine, as well as do not stand in front of the device to avoid threat triggered by residual pressure in the fish feed drifting pellet making maker dental caries;
⑧ After the fish feed floating pellet making maker is running typically, it shall not be closed down at will.
Related post: https://www.richipelletmachine.com/fish-feed-mill-plant-cost/
( 2) Power on
① Prior to beginning the fish feed drifting pellet making equipment, check the bolts, and also there must be no looseness;
② Make sure the typical supply of steam as well as water;
③ Guarantee that the power supply and electric home appliances are normal;
④ Open up the vapor shutoff, pre-heat the floating fish pellet machine blowing chamber, the temperature is about 100 degrees;
⑤ Start the fish feed floating pellet making equipment: begin the conditioner, begin the feeding auger, when there is material spurting from the outlet of the conditioner, start including steam to the conditioner.
A small amount of water is included, and also the material is fed right into the puffing tooth cavity at the same time. After the product is squeezed out by fish feed floating pellet making equipment, the puffing impact and dampness of the product are adjusted.
Related post: poultry feed plant price
( 3) Downtime
After the fish feed floating pellet making equipment manufacturing involves an end, it needs to be quit. The stop series is: feeding auger and also conditioner. After that wait until the shown value of the primary engine present on the electrical control closet ends up being the no-load existing value, then stop the primary electric motor and also the oil pump electric motor.
( When the corn is puffed, about 25 kg of soybeans should be fed into the bypass feeding port of the first area of the blowing tooth cavity. To clean up the residual corn product in the blowing cavity, and after that quit the primary motor to avoid the fish feed drifting pellet making maker from blocking), after that promptly take apart the puffing dental caries of the tail section for cleansing.
After cleansing, use grease to the inner wall of the primary shaft and screw head (After feeding oil), re-install it as well as wait on the following boot;
When you see that the material level indicator on the silo shows that the product degree has reached the lowest level, begin to prepare for shutdown. At this time, do not stop the feeding auger as well as conditioner, and also stop feeding when the major fish feed drifting pellet making device present drops to the no-load existing auger and also conditioner.
2. Operation sequence of floating fish feed equipment
( 1 )When puffing soybeans, the two areas at the inlet end of the blowing cavity are single screw heads, as well as the three areas at the outlet end are equipped with double screw heads.
Initially, include heavy steam to the coat to pre-heat the puffing cavity to regarding 100 degrees, and put the screws on the puffing dental caries at the tail section. After the plug is tightened up, loosen it for 3-4 turns, and then tighten the screw plug to repair the screw plug before feeding.
By regulating the stepless high-speed mechanism of the feeding auger, the feeding rate is from slow-moving to quick, as well as the feeding speed is from small to large. After the soybean meal is ejected from the screw plug opening, add the cover to enter the typical manufacturing, and configure the screw plugs with different apertures to obtain soybean meal with various yields as well as excellences.
By setting up the conelike pressure rings of different sizes, the suggested temperature of the four-section (discharge end) blowing cavity is 130-140 degrees. It is suggested that the sieve of the crusher utilized for squashing soybeans must have a diameter of 3-4.
( 2 )When extruding grainy feed by fish feed floating pellet making machine, the squeezing out screws in the squeezing out cavity are all solitary screw heads, add vapor to the jacket to pre-heat the puffing tooth cavity to concerning 80 degrees, and go into the fish feed floating pellet making machine and steam uniformly satiated and also tempered powder.
About 18%, this have to be carried out in the feed conditioner, and the feed quantity is controlled by the stepless speed regulating device from little to huge. Keep in mind that the reading of the ammeter of the main motor must not go beyond the rated present of the main engine of fish feed floating pellet making equipment.
Beware of straining the motor as well as squeezing out powdery products. When the temperature of the extruding chamber at the discharge end is controlled to an proper degree by configuring cone-shaped pressure rings with different sizes.
The above is the principle, framework and running treatments of the fish feed drifting pellet making machine introduced by Richi Equipment. In quest of crunchy taste as well as great appearance, manufacturers frequently add a leavening representative (or baking powder), which has a specific quantity of light weight aluminum components, and produces gas when heated during cooking or frying, and also the leavening representative is inside the food.
For details please contact: feed mill equipment manufacturers
WhatsApp：86 138 3838 9622
Email：enquiry@richipelletmachine.com
评论
发表评论